Eaton AGW-1-1/2 1.5 A 32 Vac Fast-Acting Glass Tube Fuse
Eaton AGW-1-1/2 1.5 A 32 Vac Fast-Acting Glass Tube Fuse

Eaton AGW-1-1/2 1.5 A 32 Vac Fast-Acting Glass Tube Fuse

Share
Eaton AGW-1-1/2 is a 1.5 A fast-acting glass tube fuse in a 6.3 x 22.2 mm package, rated 32 Vac, for in-line holder hhb / hhk / hrk.
    • Product Details
    • Download

    Eaton AGW-1-1/2 1.5 A 32 Vac Fast-Acting Glass Tube Fuse

    At 1.5 A, AGW-1-1/2 is the rating most often picked when the measured load lands just under the next step up in the AGW range.

    Core Specifications

    ParameterValue
    Manufacturer / SeriesEaton / AGW Series
    Part numberAGW-1-1/2
    Current rating1.5 A
    Voltage rating32 Vac
    Interrupting rating1000 A at rated Vac
    Typical DC cold resistance0.060 – 0.080 Ω
    Package1/4 x 7/8 in (6.3 x 22.2 mm) glass tube, nickel-plated brass end caps
    Packaging codeBK = 100 fuses in a cardboard carton
    Agency / environmentalBussmann AGW series, fast-acting glass tube construction

    Electrical Characteristics

    % of rating / conditionOpening time
    Inper published time-current curve

    At 1.5 A

    • Interruption. 1,000 A at the rated voltage is what this part is tested to clear. Above that the glass body ruptures rather than contains the arc, so the part only protects while the prospective fault current stays below the rating.
    • The interrupting rating here is modest by design - a glass tube of this size is a circuit protector, not a high-energy interrupter.
    • Position in the range. Sits between AGW-1 and AGW-2 in the range. Stepping down to AGW-1 trips sooner on light overload but leaves less continuous headroom; AGW-2 trades the other way.

    Where 1.5 A Fits

    In practice 1.5 A covers desktop and appliance power inlets: single-phase equipment inlets and adapter outputs. Sizing closer than 20 % to the rating leaves no room for the ambient rise inside the enclosure.

    For Procurement

    • Order AGW-1-1/2. The orderable reference on this page reads AGW-1-1/2; the packaging prefix, where the series uses one, goes in front of the part number rather than after it.
    • Agency / compliance for this rating: Bussmann AGW series, fast-acting glass tube construction.
    • 1.5 A is not interchangeable with the neighbouring rating beyond its name: the current, the terminal arrangement and the body dimensions all have to match.

    Frequently Asked Questions

    Will AGW-1-1/2 carry 1.5 A continuously without opening?
    Yes. The published table shows no opening at 100 % of rating, so 1.5 A is inside the continuous rating at 25 C. Ambient temperature inside the enclosure, not the nominal current, is what usually forces the next size up.

    What fault current can AGW-1-1/2 clear?
    1,000 A at rated voltage. That figure assumes a normal branch-circuit source impedance; a stiff transformer feeding the same circuit can exceed it, and then the fuse is no longer the protective device by design.

    Can AGW-1-1/2 replace the next rating up in an existing design?
    No. Dropping from a higher rating changes both the continuous headroom and the I2t, so a fuse that used to ride through inrush may now open on it. Match current, voltage, I2t and body before substituting.

    Design note: resistance, I2t and voltage-drop values are typical unless identified as ratings. Verify the current data sheet and curves before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products