Eaton AMLV08V18C650 MLV ESD Suppressor 650 pF
Eaton AMLV08V18C650 MLV ESD Suppressor 650 pF

Eaton AMLV08V18C650 MLV ESD Suppressor 650 pF

Share
AMLV08V18C650: multilayer varistor ESD suppressor, 23-28 V varistor voltage, 18 V working, 44 V clamp, 650 pF, 0.3 J.
    • Product Details
    • Download

    Eaton AMLV08V18C650 MLV ESD Suppressor 650 pF

    AMLV08V18C650 at a glance: multilayer varistor ESD suppressor, 23-28 V varistor voltage, 18 V working, 44 V clamp, 650 pF, 0.3 J.

    Key Specifications

    ParameterValue
    Orderable part numberAMLV08V18C650
    Working voltage, DC18 Vdc
    Working voltage, AC14 Vac
    Varistor voltage at 1 mA23 V to 28 V
    Clamping voltage at 1 A44 V
    Energy absorption, 10/1000 us0.3 J
    Peak current, 8/20 us120 A
    Typical capacitance at 1 MHz650 pF
    Vjump (5 min)24.5 V
    WLD (10 pulses)1 J
    Leakage current at working voltagemax. 20 uA
    Package0805 (2012 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1078

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    What the Numbers Mean

    A multilayer varistor sits across a signal or supply rail and does nothing until the voltage crosses its breakdown point, at which it turns into a low impedance and diverts the transient. The value that matters for the protected chip is not the varistor voltage but the clamping voltage at the surge current you expect.

    The clamp column works out at 1.73 times the varistor voltage: 44 V at the rated current against 25.5 V at 1 mA. That ratio is what the downstream part has to survive, not the 25.5 V figure on the label.

    Standing at 18 V the leakage is at most 20 uA, which is 0.36 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The 650 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the AMLV family this is item 10 of 28 in the Eaton catalogue.

    Positioning in the Range

    The part goes across the line it protects, as close to the connector or the cable entry as the layout allows. Lead length matters: every extra millimetre of trace between the connector and the varistor adds inductance and raises the voltage the protected chip actually sees.

    • Do not use a varistor as a series element or in a signal path carrying DC. It is a shunt device, and any steady current through it is a fault.
    • The varistor voltage tolerance is wide by design. Two parts of the same part number can differ by 20 percent and both be good, so the design has to work at the low end of the range.

    Frequently Asked Questions

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    How many ESD strikes can it take?
    The ESD rating is a qualification level, not a lifetime count. IEC 61000-4-2 level 4 is 8 kV contact and 15 kV air, and the part is expected to survive repeated strikes at that level because the energy per strike is small.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products