Eaton AMLV22V38C3000 Multilayer Varistor, 77 V Clamp
Eaton AMLV22V38C3000 Multilayer Varistor, 77 V Clamp

Eaton AMLV22V38C3000 Multilayer Varistor, 77 V Clamp

Share
AMLV22V38C3000: multilayer varistor ESD suppressor, 42.3-51.7 V varistor voltage, 38 V working, 77 V clamp, 3000 pF, 12 J.
    • Product Details
    • Download

    Eaton AMLV22V38C3000 Multilayer Varistor, 77 V Clamp

    AMLV22V38C3000 at a glance: multilayer varistor ESD suppressor, 42.3-51.7 V varistor voltage, 38 V working, 77 V clamp, 3000 pF, 12 J.

    Ratings at a Glance

    ParameterValue
    Orderable part numberAMLV22V38C3000
    Working voltage, DC38 Vdc
    Working voltage, AC30 Vac
    Varistor voltage at 1 mA42.3 V to 51.7 V
    Clamping voltage at 1 A77 V
    Energy absorption, 10/1000 us12 J
    Peak current, 8/20 us1000 A
    Typical capacitance at 1 MHz3000 pF
    Vjump (5 min)50 V
    WLD (10 pulses)12 J
    Leakage current at working voltagemax. 20 uA
    Package2220 (5750 metric)
    MountingSurface mount
    Operating temperature-55 °C to +125 °C
    QualificationAEC-Q200
    RoHSCompliant, halogen free
    Data sheetEaton Technical Data ELX1078

    Dimensions, recommended pad or hole pattern and the derating curves are
    on the data sheet pages; the package line above gives the body size as Eaton states it.

    Reading the Data Sheet

    In a multilayer construction the zinc oxide grains are stacked in many thin layers, so the same body height gives a higher voltage per unit area than a single-layer disc. That is how an 0402 chip reaches 18 Vdc working voltage without becoming thick.

    The clamp column works out at 1.64 times the varistor voltage: 77 V at the rated current against 47 V at 1 mA. That ratio is what the downstream part has to survive, not the 47 V figure on the label.

    Standing at 38 V the leakage is at most 20 uA, which is 0.76 mW of continuous dissipation. Small, but it is why a varistor on a battery rail has to be chosen on leakage and not only on voltage.

    The 3000 pF typical capacitance is the cost of the clamp. On a power rail it is irrelevant; on a data line it is the reason to look at the low-capacitance versions of the same voltage.

    Within the AMLV family this is item 28 of 28 in the Eaton catalogue.

    Where This Series Fits

    The return path is half the component. A varistor tied to a ground plane far from the connector leaves the loop inductance in series with the clamp, and the residual voltage at the chip is the clamp plus L di/dt.

    • Do not run the part at its varistor voltage: the working voltage column is the continuous limit, and the varistor voltage is 1.5 to 2 times higher only because the ceramic is soft at the knee.
    • The response time is quoted below a nanosecond because the ceramic turns conductive in the grain boundaries, not because of a junction.

    Frequently Asked Questions

    Does the package size change the electrical ratings?
    Yes, the energy and peak current scale with the body volume, so a 0402 and a 1206 of the same voltage are not interchangeable on a surge.

    Is the varistor voltage the same as the working voltage?
    No. The working voltage is the continuous DC or AC level the part can sit at; the varistor voltage is measured at 1 mA and is typically 1.5 to 2 times higher. Sizing on the varistor voltage would put the part into conduction on a normal rail.

    What does the capacitance do to my signal?
    It loads the line. At 1 MHz a 100 pF part is about 1.6 kOhm of reactance, which is harmless on a power rail and fatal on a 480 Mbit USB pair. Choose a low-capacitance version when the line carries data.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products