Eaton CC06FA1.5A 1.5 A 63 Vdc Automotive Chip Fuse
Eaton CC06FA1.5A 1.5 A 63 Vdc Automotive Chip Fuse

Eaton CC06FA1.5A 1.5 A 63 Vdc Automotive Chip Fuse

Share
Eaton CC06FA1.5A is a 1.5 A, 63 Vdc automotive grade fast-acting chip fuse in an 0603 package, AEC-Q200 qualified, for BMS and body control modules. Ordering code CC06FA1-5A-TR.
    • Product Details
    • Download

    Eaton CC06FA1.5A 1.5 A 63 Vdc Automotive Chip Fuse

    The CC06FA1.5A is the 1.5 A part of the CC06FA family - an 0603 (1608 metric) chip fuse rated 63 Vdc with 50 A interrupting capacity. Supplied as CC06FA1-5A-TR - 5,000 pieces in paper tape on a 178 mm (7 inch) reel.

    Core Specifications

    ParameterValue
    Manufacturer / SeriesEaton / CC06FA Series
    Orderable part numberCC06FA1.5A (RoHS suffix -R form CC06FAxxx-R)
    Ordering codeCC06FA1-5A-TR
    Packaging5,000 pcs in paper tape, 178 mm (7 in) reel
    Current rating1.5 A
    Voltage rating63 Vdc
    Interrupting rating50 A
    Typical DC cold resistance0.086 Ohm
    Typical pre-arcing I2t0.0319 A2s
    Typical voltage drop0.138 V
    Part markingK
    Package0603 (1608 metric) surface mount chip, ceramic and glass construction
    AEC-Q200qualified
    Lead freeyes
    Agency / environmentalUL Recognized file E19180; AEC-Q200 qualified

    Electrical Characteristics

    % of rating / conditionOpening time
    100 %4 hours minimum
    200 %60 seconds maximum

    At 1.5 A

    • Heat at this rating. 138 mV drop across 1.5 A works out to 0.207 W in the element; the cold resistance of 0.086 Ohm would suggest only 0.1935 W, so the rest is the element's own temperature rise. Layout the copper for the higher figure.
    • Interruption. 50 A at the rated voltage is what this part is tested to clear. Above that the enclosure rather than the element decides what happens, so the prospective fault current is part of the application check, not only the load.
    • Position in the range. Tops the range, one step above CC06FA1.25A. A larger current needs a different series or two devices in parallel - there is no bigger part in this body.

    Where 1.5 A Fits

    On the DC side 1.5 A is sized from the continuous battery or bus current plus the ambient derating, not from a branch-circuit rule of thumb. Check the prospective short-circuit current against the breaking capacity in the table before fixing the rating.

    For Procurement

    • Order CC06FA1.5A. The orderable reference on this page reads CC06FA1.5A (RoHS suffix -R form CC06FAxxx-R); the packaging prefix, where the series uses one, goes in front of the part number rather than after it.
    • Agency / compliance for this rating: UL Recognized file E19180; AEC-Q200 qualified.
    • 1.5 A is not interchangeable with the neighbouring rating beyond its name: the current, the terminal arrangement and the body dimensions all have to match.

    Frequently Asked Questions

    Can CC06FA1.5A replace the next rating up in an existing design?
    No. Dropping from a higher rating changes both the continuous headroom and the I2t, so a fuse that used to ride through inrush may now open on it. Match current, voltage, I2t and body before substituting.

    What fault current can CC06FA1.5A clear?
    50 A at rated voltage. That figure assumes a normal branch-circuit source impedance; a stiff transformer feeding the same circuit can exceed it, and then the fuse is no longer the protective device by design.

    Will CC06FA1.5A carry 1.5 A continuously without opening?
    Yes. The published table shows no opening at 100 % of rating, so 1.5 A is inside the continuous rating at 25 C. Ambient temperature inside the enclosure, not the nominal current, is what usually forces the next size up.

    Design note: resistance, I2t and voltage-drop values are typical unless identified as ratings. Verify the current data sheet and curves before release.

    Mechanical Dimensions

    eaton-cc06fa-automotive-fast-acting-chip-surface-mount-fuse-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message