Eaton CL1110-4-100TR-R 4-Phase VRM Inductor 100 nH per phase, 15 A Rated
Eaton CL1110-4-100TR-R 4-Phase VRM Inductor 100 nH per phase, 15 A Rated

Eaton CL1110-4-100TR-R 4-Phase VRM Inductor 100 nH per phase, 15 A Rated

Share
Eaton CL1110-4-100TR-R: 4-phase multi-phase power inductor, 100 nH per phase, 0.63 mOhm DCR, 15 A rated per phase.
    • Product Details
    • Download

    Eaton CL1110-4-100TR-R 4-Phase VRM Inductor 100 nH per phase, 15 A Rated

    CL1110-4-100TR-R at a glance: 4-phase multi-phase power inductor, 0.63 mOhm DCR, 15 A rated current per phase.

    Key Specifications

    ParameterValue
    Orderable part numberCL1110-4-100TR-R
    Number of phases4
    Rated inductance per phase100 nH ±20%
    Open circuit inductance (OCL)470 nH / 450 nH (per pin pair)
    Full load inductance (FLL)340 nH minimum
    DC resistance (DCR)0.63 mOhm
    Rated current per phase15 A
    PackageCL1110 footprint (see drawing)
    PackagingTR - tape and reel
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    With 4 phases of 100 nH each, the ripple on a given rail is the sum of the individual phase currents. Adding phases does not just divide the current - it also shapes the ripple, which is why the phase count is part of the VRM design rather than a purchasing decision.

    DCR 0.63 mOhm at 20 °C is the number that sets efficiency. At 15 A per phase the winding loss is 0.1 W per phase; add the core loss and the phase count to get the total inductor loss in the converter.

    Series Positioning

    CL1110 是 100 nH 的多相电感,2 / 4 / 6 相,OCL 到 470 nH。

    • Typical use: 多相 VRM、大电流 POL.
    • OCL 是在 0 Adc 下测的,带载后实际电感会掉到 FLL 的水平,纹波计算要用 FLL。
    • Data sheet 4310; test conditions 1 MHz / 0.1 Vrms, +25 °C unless stated.

    OCL is the open-circuit inductance: 470 nH / 450 nH (per pin pair) measured with no DC bias. In the circuit the core is biased by the phase current and the inductance falls - the datasheet gives FLL as the value at rated current, and that is the number to use for ripple calculation. 4 phases is the common configuration for a mid-power VRM. The phase count is set by the converter, not by the inductor - what matters here is that this part is the 4-phase variant with the matching pinout and DCR.

    Frequently Asked Questions

    What does the phase count mean?
    The number of independent windings sharing the same footprint. More phases means lower current per phase, lower copper loss and better ripple cancellation.

    Can I use fewer phases than the part number?
    No. The part number fixes the phase count and the pinout that goes with it.

    What does the phase count mean?
    The number of independent windings sharing the same footprint. More phases means lower current per phase, lower copper loss and better ripple cancellation.

    Design note: use the full-load inductance and the hot-case
    DCR for the loss budget, and check the layout keeps each phase current loop closed.

    Mechanical Dimensions

    eaton-cl1110-multi-phase-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products