Eaton CLB1108-2-50TR-R 2-Phase VRM Inductor 50 nH per phase, 25 A Rated
Eaton CLB1108-2-50TR-R 2-Phase VRM Inductor 50 nH per phase, 25 A Rated

Eaton CLB1108-2-50TR-R 2-Phase VRM Inductor 50 nH per phase, 25 A Rated

Share
Eaton CLB1108-2-50TR-R: 2-phase multi-phase power inductor, 50 nH per phase, 0.28 mOhm DCR, 25 A rated per phase.
    • Product Details
    • Download

    Eaton CLB1108-2-50TR-R 2-Phase VRM Inductor 50 nH per phase, 25 A Rated

    CLB1108-2-50TR-R: 2-phase power inductor, OCL 200 nH at 0 Adc, 150 nH at 25 A, 100 nH at 23 A, DCR 0.28 mOhm, 25 A per phase.

    Key Specifications

    ParameterValue
    Orderable part numberCLB1108-2-50TR-R
    Rated inductance per phase50 nH ±20%
    Number of phases2
    Open circuit inductance (OCL)200 nH at 0 Adc, 150 nH at 25 A, 100 nH at 23 A
    DC resistance (DCR)0.28 mOhm
    Rated current per phase25 A
    Peak current per phase110 A
    PackageCLB1108 footprint (see drawing)
    PackagingTR - tape and reel
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A multi-phase inductor splits one input into several smaller rails so that each phase carries a fraction of the total current. The point is copper loss: total loss goes as I²R, so dividing the current across 2 phases cuts the resistive loss by roughly the square of the phase count, and lets the magnetics run at a lower flux density.

    Copper loss rises with temperature - roughly half the DCR change over the working range. A part running hot is a part with more loss, which is a feedback loop worth keeping an eye on in a densely populated board.

    Where This Series Fits

    CLB1108 是 50 nH 多相电感,给出 OCL 在 Isat1 与 Isat2 两个偏置点的值。

    • Typical use: 多相 VRM、高频大电流供电.
    • CLB 的 OCL 随偏置下降得比标准件慢(150 nH @25 A),这是它相对同尺寸其它系列的核心差别。
    • Data sheet Volterra; test conditions 1 MHz / 0.1 Vrms, +25 °C unless stated.

    Isat marks where the part leaves its inductive region. At 25 A the inductance has already dropped well below its open-circuit value, so a design that runs close to that point trades ripple control for headroom. Two phases is the entry point of the family: one extra winding against the single-phase alternative, halving the current in each winding at the cost of a slightly larger footprint and one more layer of control.

    Frequently Asked Questions

    Is this part RoHS compliant?
    Yes - the -R suffix on the part number denotes the RoHS build.

    Which inductance should I use?
    The rated inductance per phase, not the OCL. OCL is measured at zero bias; FLL is what the part has at rated current and it is the number the ripple calculation needs.

    Can I use fewer phases than the part number?
    No. The part number fixes the phase count and the pinout that goes with it.

    Design note: use the full-load inductance and the hot-case
    DCR for the loss budget, and check the layout keeps each phase current loop closed.

    Mechanical Dimensions

    eaton-clb1108-multi-phase-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products