Eaton CLH1110R1-5-R050-R Multi-Phase Power Inductor, 5 phases, 50 nH per phase
Eaton CLH1110R1-5-R050-R Multi-Phase Power Inductor, 5 phases, 50 nH per phase

Eaton CLH1110R1-5-R050-R Multi-Phase Power Inductor, 5 phases, 50 nH per phase

Share
Eaton CLH1110R1-5-R050-R: 5-phase multi-phase power inductor, 50 nH per phase, 0.23 mOhm DCR, 25 A rated per phase.
    • Product Details
    • Download

    Eaton CLH1110R1-5-R050-R Multi-Phase Power Inductor, 5 phases, 50 nH per phase

    CLH1110R1-5-R050-R: 5-phase power inductor, OCL 300 nH typical / 240 nH minimum, DCR 0.23 mOhm, 25 A per phase.

    Electrical Specifications

    ParameterValue
    Orderable part numberCLH1110R1-5-R050-R
    Number of phases5
    Rated inductance per phase50 nH ±20%
    Open circuit inductance (OCL)300 nH typical / 240 nH minimum
    Full load inductance (FLL)200 nH minimum
    DC resistance (DCR)0.23 mOhm
    Rated current per phase25 A
    Peak current per phase140 A
    PackageCLH1110 footprint (see drawing)
    PackagingTR - tape and reel
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    The 25 A per phase rating is set by the winding and the core, not by the load. Design the converter so every phase shares the current evenly; an unbalanced phase reaches its limit long before the average current does.

    DCR 0.23 mOhm at 20 °C is the number that sets efficiency. At 25 A per phase the winding loss is 0.1 W per phase; add the core loss and the phase count to get the total inductor loss in the converter.

    Where This Series Fits

    CLH1110R1 是 R1 版 50 nH 多相电感,OCL 300 nH,DCR 低到 0.23 mOhm。

    • Typical use: 服务器多相 VRM、高端 GPU 供电.
    • H 系列是 CL 系列里 DCR 最低的一档,适合对效率敏感的场合。
    • Data sheet 4313; test conditions 1 MHz / 0.1 Vrms, +25 °C unless stated.

    Isat marks where the part leaves its inductive region. At 25 A the inductance has already dropped well below its open-circuit value, so a design that runs close to that point trades ripple control for headroom. 5 phases is a high-current configuration. Per-phase current is low enough that copper loss stays small even with 25 A in each winding, which is the whole point of going to this many phases.

    Frequently Asked Questions

    Which inductance should I use?
    The rated inductance per phase, not the OCL. OCL is measured at zero bias; FLL is what the part has at rated current and it is the number the ripple calculation needs.

    What is Isat?
    The current at which the inductance starts to fall away. It is a magnetic limit, not a thermal one, and it is the point at which ripple control starts to go.

    Which inductance should I use?
    The rated inductance per phase, not the OCL. OCL is measured at zero bias; FLL is what the part has at rated current and it is the number the ripple calculation needs.

    Design note: use the full-load inductance and the hot-case
    DCR for the loss budget, and check the layout keeps each phase current loop closed.

    Mechanical Dimensions

    eaton-clh1110-multi-phase-inductor-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products