Eaton CMS1-9-R Common-Mode Noise Suppressor, 62 uH
Eaton CMS1-9-R Common-Mode Noise Suppressor, 62 uH

Eaton CMS1-9-R Common-Mode Noise Suppressor, 62 uH

Share
Eaton CMS1-9-R: 62 uH common-mode inductor, 1.9 A Irms, 0.035 ohm DCR, surface mount.
    • Product Details
    • Download

    Eaton CMS1-9-R Common-Mode Noise Suppressor, 62 uH

    CMS1-9-R at a glance: 62 uH common-mode inductor, 1.9 A Irms, 0.035 ohm DCR, surface mount.

    Product Specifications

    ParameterValue
    Orderable part numberCMS1-9-R
    I rms (max)1.9 A
    Open circuit inductance (OCL)62 uH minimum, (1-2) & (4-3)
    DCR typical @ 20 °C (1-2)0.035 ohm
    DCR typical @ 20 °C (4-3)0.035 ohm
    Leakage inductance typ0.68 uH
    Interwinding capacitance typ2.7 pF
    PackageCMS series, surface mount
    Operating temperature160 °C maximum
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    The impedance figure is measured across the winding pair, which is exactly the common-mode path. That is why these parts are picked by impedance at the noise frequency rather than by inductance.

    For a DC-DC output filter this is the part that decides whether the noise stays inside the conducted limits, and how much margin the design keeps at the top of the load step. 62 uH is the working middle of the CMS range: enough inductance to hold down the ripple on a rail, small enough that the 1.9 A Irms rating is not the thing limiting the design.

    Where This Series Fits

    CMS 是贴片共模电感,CMS1 / CMS2 / CMS3 三个尺寸系列,4.5 uH 到 1310 uH。

    • Typical use: 开关电源输出滤波、DC-DC 共模抑制、EMI 整改.
    • CMS 的 OCL 是在 (1-2) 与 (4-3) 两组绕组上测的最小值,实际应用中两根线都要接对绕组。
    • Data sheet 4313.

    The 62 uH of common-mode inductance is what blocks the noise; the 0.68 uH of leakage inductance is what gets past, and the 2.7 pF of interwinding capacitance is what couples across the windings at high frequency. CMS1 is the smallest of the three CMS footprints

    Frequently Asked Questions

    What impedance should I pick?
    The one that gives the attenuation you need at the noise frequency of your circuit, then check that the DCR is acceptable on the signal.

    Does it affect my signal?
    Only through DCR and the small amount of leakage inductance. The differential signal is not filtered by design.

    Does it affect my signal?
    Only through DCR and the small amount of leakage inductance. The differential signal is not filtered by design.

    Design note: pick the choke by impedance at the noise
    frequency, then confirm DCR and rated current against the signal or the rail.

    Mechanical Dimensions

    eaton-cms-common-mode-inductors-surface-mount-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products