Eaton CMT2-3-R Through-Hole Common Mode Inductor
Eaton CMT2-3-R Through-Hole Common Mode Inductor

Eaton CMT2-3-R Through-Hole Common Mode Inductor

Share
Eaton CMT2-3-R: Through-Hole Common Mode Choke, 12 mH, 2.45 A, DCR 135 mOhm.
    • Product Details
    • Download

    Eaton CMT2-3-R Through-Hole Common Mode Inductor

    Discontinued series. Eaton marked CMT discontinued effective 1 March 2016, or while inventory lasts. It is listed here as a service part for existing designs - specify a current production common-mode choke for new work.
    CMT2-3-R at a glance: through-hole common-mode choke, 12 mH per winding, 2.45 A rms, DCR 135 mOhm per winding.

    Key Specifications

    ParameterValue
    Orderable part numberCMT2-3-R
    Open circuit inductance (1-2), minimum12 mH
    Open circuit inductance (4-3), minimum12 mH
    Irms, maximum2.45 A
    DCR typical @ 20 °C (1-2)135 mOhm
    DCR typical @ 20 °C (4-3)135 mOhm
    MountingThrough-hole, 4 pins
    FlammabilityUL94V-0
    Operating temperature-40 °C to +125 °C
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A common-mode choke on the AC input works because the mains current flows in opposite directions through the two windings, so the signal sees almost nothing while the common-mode noise sees the full impedance. It is the first stage of nearly every off-line filter.

    The rated current is the RMS line current at the stated temperature rise, and the inductance is what remains under that current. A common-mode choke does not see differential DC, so saturation is not the usual failure mode here - heating is.

    The two windings are measured separately, (1-2) and (4-3), because a mismatch between them turns common-mode noise into differential noise - which the X-cap then has to absorb.

    Where This Series Fits

    CMT is a through-hole common-mode choke for the AC input of an off-line supply, with attenuation up to 68 dB and inductance from 0.53 mH to 66 mH. It sits ahead of the bridge and stops switching noise from travelling back down the mains lead.

    • Typical applications: Off-line power supplies, EMI filters, AC input of switching regulators, DC-DC converters, computer/TV/audio equipment.
    • Eaton marked this series discontinued effective 1 March 2016 or while inventory lasts - treat it as a service part for existing designs, not a new-design choice.
    • Data sheet 4312.

    Sizing It Into a Design

    Choose 12 mH when the ripple target is in the middle of the range of the design window: the DCR stays at 135 mOhm and the saturation limit at - A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Why is there a separate OCL for each winding?
    The two windings are measured separately, (1-2) and (4-3). A mismatch between them means an asymmetry in the differential impedance, so both are specified.

    Why is there a separate OCL for each winding?
    The two windings are measured separately, (1-2) and (4-3). A mismatch between them means an asymmetry in the differential impedance, so both are specified.

    Why is there a separate OCL for each winding?
    The two windings are measured separately, (1-2) and (4-3). A mismatch between them means an asymmetry in the differential impedance, so both are specified.

    Design note: rated for RMS line current, not inrush. The choke sits upstream of the bridge and downstream of the fuse - size the fuse first.

    Mechanical Dimensions

    eaton-cmt-common-mode-inductors-through-hole-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message