Eaton CMT3-2-R Through-Hole Common Mode Inductor
Eaton CMT3-2-R Through-Hole Common Mode Inductor

Eaton CMT3-2-R Through-Hole Common Mode Inductor

Share
Eaton CMT3-2-R: Through-Hole Common Mode Choke, 3.5 mH, 2.6 A, DCR 80 mOhm.
    • Product Details
    • Download

    Eaton CMT3-2-R Through-Hole Common Mode Inductor

    Discontinued series. Eaton marked CMT discontinued effective 1 March 2016, or while inventory lasts. It is listed here as a service part for existing designs - specify a current production common-mode choke for new work.
    CMT3-2-R at a glance: through-hole common-mode choke, 3.5 mH per winding, 2.6 A rms, DCR 80 mOhm per winding.

    Key Specifications

    ParameterValue
    Orderable part numberCMT3-2-R
    Open circuit inductance (1-2), minimum3.5 mH
    Open circuit inductance (4-3), minimum3.5 mH
    Irms, maximum2.6 A
    DCR typical @ 20 °C (1-2)80 mOhm
    DCR typical @ 20 °C (4-3)80 mOhm
    MountingThrough-hole, 4 pins
    FlammabilityUL94V-0
    Operating temperature-40 °C to +125 °C
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Off-line supplies need a choke that will take the full AC line current without saturating, and still present a high impedance to the noise that tries to leave through the mains lead. That is the CMT.

    The rated current is the RMS line current at the stated temperature rise, and the inductance is what remains under that current. A common-mode choke does not see differential DC, so saturation is not the usual failure mode here - heating is.

    The two windings are measured separately, (1-2) and (4-3), because a mismatch between them turns common-mode noise into differential noise - which the X-cap then has to absorb.

    Series Positioning

    CMT is a through-hole common-mode choke for the AC input of an off-line supply, with attenuation up to 68 dB and inductance from 0.53 mH to 66 mH. It sits ahead of the bridge and stops switching noise from travelling back down the mains lead.

    • Typical applications: Off-line power supplies, EMI filters, AC input of switching regulators, DC-DC converters, computer/TV/audio equipment.
    • Eaton marked this series discontinued effective 1 March 2016 or while inventory lasts - treat it as a service part for existing designs, not a new-design choice.
    • Data sheet 4312.

    Putting It to Work

    At 3.5 mH this part is at the low-inductance end of the family. The winding that produces that inductance is also what sets the 80 mOhm DCR - more turns, thinner wire, more resistance.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Why is there a separate OCL for each winding?
    The two windings are measured separately, (1-2) and (4-3). A mismatch between them means an asymmetry in the differential impedance, so both are specified.

    Does it filter differential noise?
    Not by design. The leakage inductance does provide a small differential impedance, but it is a by-product; use an X-capacitor and a differential choke for that.

    Why is there a separate OCL for each winding?
    The two windings are measured separately, (1-2) and (4-3). A mismatch between them means an asymmetry in the differential impedance, so both are specified.

    Design note: rated for RMS line current, not inrush. The choke sits upstream of the bridge and downstream of the fuse - size the fuse first.

    Mechanical Dimensions

    eaton-cmt-common-mode-inductors-through-hole-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products