Eaton CMT4-4-R Through-Hole Common Mode Inductor
Eaton CMT4-4-R Through-Hole Common Mode Inductor

Eaton CMT4-4-R Through-Hole Common Mode Inductor

Share
Eaton CMT4-4-R: Through-Hole Common Mode Choke, 1.3 mH, 4 A, DCR 32 mOhm.
    • Product Details
    • Download

    Eaton CMT4-4-R Through-Hole Common Mode Inductor

    Discontinued series. Eaton marked CMT discontinued effective 1 March 2016, or while inventory lasts. It is listed here as a service part for existing designs - specify a current production common-mode choke for new work.
    CMT4-4-R at a glance: through-hole common-mode choke, 1.3 mH per winding, 4 A rms, DCR 32 mOhm per winding.

    Electrical Specifications

    ParameterValue
    Orderable part numberCMT4-4-R
    Open circuit inductance (1-2), minimum1.3 mH
    Open circuit inductance (4-3), minimum1.3 mH
    Irms, maximum4 A
    DCR typical @ 20 °C (1-2)32 mOhm
    DCR typical @ 20 °C (4-3)32 mOhm
    MountingThrough-hole, 4 pins
    FlammabilityUL94V-0
    Operating temperature-40 °C to +125 °C
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    This is a through-hole off-line common-mode choke: two windings on one ferrite toroid, attenuation up to 68 dB, and inductance values that put the corner frequency well below the switching fundamental.

    The rated current is the RMS line current at the stated temperature rise, and the inductance is what remains under that current. A common-mode choke does not see differential DC, so saturation is not the usual failure mode here - heating is.

    The two windings are measured separately, (1-2) and (4-3), because a mismatch between them turns common-mode noise into differential noise - which the X-cap then has to absorb.

    Series Positioning

    CMT is a through-hole common-mode choke for the AC input of an off-line supply, with attenuation up to 68 dB and inductance from 0.53 mH to 66 mH. It sits ahead of the bridge and stops switching noise from travelling back down the mains lead.

    • Typical applications: Off-line power supplies, EMI filters, AC input of switching regulators, DC-DC converters, computer/TV/audio equipment.
    • Eaton marked this series discontinued effective 1 March 2016 or while inventory lasts - treat it as a service part for existing designs, not a new-design choice.
    • Data sheet 4312.

    Putting It to Work

    1.3 mH sits at the low-inductance end of the range, and the trade at that point is explicit: 32 mOhm of DCR against - A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Does it filter differential noise?
    Not by design. The leakage inductance does provide a small differential impedance, but it is a by-product; use an X-capacitor and a differential choke for that.

    Why is there a separate OCL for each winding?
    The two windings are measured separately, (1-2) and (4-3). A mismatch between them means an asymmetry in the differential impedance, so both are specified.

    What is the isolation like?
    The two windings share a core and are not a safety barrier - the insulation is functional, not reinforced.

    Design note: rated for RMS line current, not inrush. The choke sits upstream of the bridge and downstream of the fuse - size the fuse first.

    Mechanical Dimensions

    eaton-cmt-common-mode-inductors-through-hole-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message