Eaton CPLE-4-50TR-R 4-Phase VRM Inductor, 40 A
Eaton CPLE-4-50TR-R 4-Phase VRM Inductor, 40 A

Eaton CPLE-4-50TR-R 4-Phase VRM Inductor, 40 A

Share
Eaton CPLE-4-50TR-R: Multi-Phase Coupled Power Inductor, Light-Load Optimised, 50 nH per phase, 40 A, DCR 0.5 mOhm.
    • Product Details
    • Download

    Eaton CPLE-4-50TR-R 4-Phase VRM Inductor, 40 A

    CPLE-4-50TR-R at a glance: 4-phase coupled inductor, 50 nH per phase, DCR 0.5 mOhm, 40 A rated per phase.

    Key Specifications

    ParameterValue
    Orderable part numberCPLE-4-50TR-R
    Number of phases4
    Rated inductance per phase50 nH/phase
    DCR nominal @ 25 °C0.5 mOhm
    DCR maximum @ 25 °C0.6 mOhm
    Rated current per phase40 A
    OCL, per pin pair490 nH typical / 365 nH minimum
    Magnetising inductance @ 5 Adc400 nH
    Frequency rangeup to 2 MHz
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    Coupling is the whole point of this family. Fifty nanohenries per phase, wound on a shared core, so that the ripple from one phase subtracts from its neighbours instead of adding. The result is a converter that can run at a lower switching frequency for the same output ripple.

    The arithmetic is the usual one for coupled windings: parallel gives L/4 with 2x the current capability, series gives 4L with half. DCR follows the same rule - parallel halves the resistance, series doubles it.

    The per-phase DCR is what sets the conduction loss, and the coupling is what sets the ripple. Neither number alone tells you whether the part will work in a given controller.

    Positioning in the Range

    CPLE uses a core material optimised for light-load efficiency: the same 50 nH per phase, but lower core loss when the converter is idling, which is where a server or a notebook spends most of its life.

    • Typical applications: Multiphase VRMs with light-load efficiency targets, Vcore rails, point-of-load.
    • The benefit shows up at light load; at full load the difference against CPL is small, so size for the load profile you actually have.
    • Data sheet 4362.

    Sizing It Into a Design

    At 50 nH per phase this part is at the design point the controller expects of the family. The winding that produces that inductance is also what sets the 0.5 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Why is the rated inductance given per phase?
    Because the windings are separate phases sharing a core. The per-phase value is what sets each phase current ripple.

    Are CPL, CPLA and CPLE interchangeable?
    Electrically similar, mechanically different: CPLA adds acoustic dampening and CPLE uses a core optimised for light-load efficiency. Confirm with the reference design.

    Why is the rated inductance given per phase?
    Because the windings are separate phases sharing a core. The per-phase value is what sets each phase current ripple.

    Design note: use the per-phase rated inductance, not the OCL, and confirm the controller is the one the family was characterised with.

    Mechanical Dimensions

    eaton-cpl-cpla-cple-multi-phase-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message