Eaton DR1030-1R8-R 1.8 uH Shielded Drum Core Inductor
Eaton DR1030-1R8-R 1.8 uH Shielded Drum Core Inductor

Eaton DR1030-1R8-R 1.8 uH Shielded Drum Core Inductor

Share
Eaton DR1030-1R8-R: Shielded Drum Core Power Inductor, 1.8 uH, 5.9 A, DCR 9.1 mOhm.
    • Product Details
    • Download

    Eaton DR1030-1R8-R 1.8 uH Shielded Drum Core Inductor

    DR1030-1R8-R at a glance: shielded drum core inductor, 1.8 uH, 5.9 A Irms, 7.4 A Isat, DCR 9.1 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR1030-1R8-R
    Rated inductance1.8 uH ±20%
    Open circuit inductance (OCL)1.9 uH
    Irms (40 °C rise)5.9 A
    Isat7.4 A
    DCR typical @ 20 °C9.1 mOhm
    DCR maximum @ 20 °C11 mOhm
    K-factor (Bp-p = K x L x dI)17
    Package10.5 x 10.3 mm footprint, 3.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    DCR 9.1 mOhm is the conduction loss: at the rated current it dissipates about 0.32 W, and that heat has to leave through the terminals and the board.

    Isat is the peak current for approximately 35% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    The DR1030 is the low-profile member of the 10.5 x 10.3 mm DR family. Eaton builds the same 10.5 x 10.3 footprint in three heights - 3.0, 4.0 and 5.0 mm - and the height is what you trade for current. The 3.0 mm part fits under a shield can or into a slim chassis; for the same inductance the taller versions will carry more current.

    • Typical applications: LED/LCD backlighting, HDTV, server and desktop power supplies, notebook regulators, graphics cards, point-of-load modules.
    • At 3.0 mm this is the thermally tightest of the three heights - check the self-heating at the current you actually need before banking on the headline Irms figure.
    • Data sheet 4132.

    Sizing and Layout Notes

    1.8 uH is at the low end of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1030-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products