Eaton DR1030-3R9-R 3.9 uH Shielded Power Inductor, 4.3 A
Eaton DR1030-3R9-R 3.9 uH Shielded Power Inductor, 4.3 A

Eaton DR1030-3R9-R 3.9 uH Shielded Power Inductor, 4.3 A

Share
Eaton DR1030-3R9-R: Shielded Drum Core Power Inductor, 3.9 uH, 4.3 A, DCR 16.4 mOhm.
    • Product Details
    • Download

    Eaton DR1030-3R9-R 3.9 uH Shielded Power Inductor, 4.3 A

    DR1030-3R9-R at a glance: shielded drum core inductor, 3.9 uH, 4.3 A Irms, 5.1 A Isat, DCR 16.4 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR1030-3R9-R
    Rated inductance3.9 uH ±20%
    Open circuit inductance (OCL)4 uH
    Irms (40 °C rise)4.3 A
    Isat5.1 A
    DCR typical @ 20 °C16.4 mOhm
    DCR maximum @ 20 °C20 mOhm
    K-factor (Bp-p = K x L x dI)12
    Package10.5 x 10.3 mm footprint, 3.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    DCR 16.4 mOhm is the conduction loss: at the rated current it dissipates about 0.30 W, and that heat has to leave through the terminals and the board.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    The DR1030 is the low-profile member of the 10.5 x 10.3 mm DR family. Eaton builds the same 10.5 x 10.3 footprint in three heights - 3.0, 4.0 and 5.0 mm - and the height is what you trade for current. The 3.0 mm part fits under a shield can or into a slim chassis; for the same inductance the taller versions will carry more current.

    • Typical applications: LED/LCD backlighting, HDTV, server and desktop power supplies, notebook regulators, graphics cards, point-of-load modules.
    • At 3.0 mm this is the thermally tightest of the three heights - check the self-heating at the current you actually need before banking on the headline Irms figure.
    • Data sheet 4132.

    Putting It to Work

    At 3.9 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 16.4 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1030-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products