Eaton DR1030-5R2-R - 5.2 uH 3.7 A Shielded Inductor
Eaton DR1030-5R2-R - 5.2 uH 3.7 A Shielded Inductor

Eaton DR1030-5R2-R - 5.2 uH 3.7 A Shielded Inductor

Share
Eaton DR1030-5R2-R: Shielded Drum Core Power Inductor, 5.2 uH, 3.7 A, DCR 22.9 mOhm.
    • Product Details
    • Download

    Eaton DR1030-5R2-R - 5.2 uH 3.7 A Shielded Inductor

    DR1030-5R2-R at a glance: shielded drum core inductor, 5.2 uH, 3.7 A Irms, 4.75 A Isat, DCR 22.9 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR1030-5R2-R
    Rated inductance5.2 uH ±20%
    Open circuit inductance (OCL)5.2 uH
    Irms (40 °C rise)3.7 A
    Isat4.75 A
    DCR typical @ 20 °C22.9 mOhm
    DCR maximum @ 20 °C27.5 mOhm
    K-factor (Bp-p = K x L x dI)10
    Package10.5 x 10.3 mm footprint, 3.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    The DC resistance sets the efficiency floor. 22.9 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Where This Series Fits

    The DR1030 is the low-profile member of the 10.5 x 10.3 mm DR family. Eaton builds the same 10.5 x 10.3 footprint in three heights - 3.0, 4.0 and 5.0 mm - and the height is what you trade for current. The 3.0 mm part fits under a shield can or into a slim chassis; for the same inductance the taller versions will carry more current.

    • Typical applications: LED/LCD backlighting, HDTV, server and desktop power supplies, notebook regulators, graphics cards, point-of-load modules.
    • At 3.0 mm this is the thermally tightest of the three heights - check the self-heating at the current you actually need before banking on the headline Irms figure.
    • Data sheet 4132.

    Putting It to Work

    5.2 uH sits in the middle of the range, and the trade at that point is explicit: 22.9 mOhm of DCR against 4.75 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1030-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products