Eaton DR1030-820-R 82 uH Shielded Power Inductor, 1 A
Eaton DR1030-820-R 82 uH Shielded Power Inductor, 1 A

Eaton DR1030-820-R 82 uH Shielded Power Inductor, 1 A

Share
Eaton DR1030-820-R: Shielded Drum Core Power Inductor, 82 uH, 1 A, DCR 332 mOhm.
    • Product Details
    • Download

    Eaton DR1030-820-R 82 uH Shielded Power Inductor, 1 A

    DR1030-820-R at a glance: shielded drum core inductor, 82 uH, 1 A Irms, 1.14 A Isat, DCR 332 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR1030-820-R
    Rated inductance82 uH ±20%
    Open circuit inductance (OCL)82 uH
    Irms (40 °C rise)1 A
    Isat1.14 A
    DCR typical @ 20 °C332 mOhm
    DCR maximum @ 20 °C382 mOhm
    K-factor (Bp-p = K x L x dI)2.6
    Package10.5 x 10.3 mm footprint, 3.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    At 332 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Series Positioning

    The DR1030 is the low-profile member of the 10.5 x 10.3 mm DR family. Eaton builds the same 10.5 x 10.3 footprint in three heights - 3.0, 4.0 and 5.0 mm - and the height is what you trade for current. The 3.0 mm part fits under a shield can or into a slim chassis; for the same inductance the taller versions will carry more current.

    • Typical applications: LED/LCD backlighting, HDTV, server and desktop power supplies, notebook regulators, graphics cards, point-of-load modules.
    • At 3.0 mm this is the thermally tightest of the three heights - check the self-heating at the current you actually need before banking on the headline Irms figure.
    • Data sheet 4132.

    Putting It to Work

    Choose 82 uH when the ripple target is at the high end of the design window: the DCR stays at 332 mOhm and the saturation limit at 1.14 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1030-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message