Eaton DR1040-100-R - 10 uH 3.8 A Shielded Inductor
Eaton DR1040-100-R - 10 uH 3.8 A Shielded Inductor

Eaton DR1040-100-R - 10 uH 3.8 A Shielded Inductor

Share
Eaton DR1040-100-R: Shielded Drum Core Power Inductor, 10 uH, 3.8 A, DCR 26 mOhm.
    • Product Details
    • Download

    Eaton DR1040-100-R - 10 uH 3.8 A Shielded Inductor

    DR1040-100-R at a glance: shielded drum core inductor, 10 uH, 3.8 A Irms, 4.4 A Isat, DCR 26 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR1040-100-R
    Rated inductance10 uH ±20%
    Open circuit inductance (OCL)9.6 uH
    Irms (40 °C rise)3.8 A
    Isat4.4 A
    DCR typical @ 20 °C26 mOhm
    DCR maximum @ 20 °C35 mOhm
    K-factor (Bp-p = K x L x dI)5.7
    Package10.5 x 10.3 mm footprint, 4.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    DCR 26 mOhm is the conduction loss: at the rated current it dissipates about 0.38 W, and that heat has to leave through the terminals and the board.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 35% rolloff at +25 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    What This Family Is For

    The DR1040 sits between the 3.0 mm DR1030 and the 5.0 mm DR1050 on the same 10.5 x 10.3 mm pad. It exists so that a design can move up in current without redoing the land pattern - the footprint is identical across all three.

    • Typical applications: Server and desktop power supplies, graphics cards, point-of-load modules, portable electronics, printers and peripherals.
    • Same pad as DR1030 and DR1050, so a height change is a drop-in swap on an existing board - the electrical limits change, the layout does not.
    • Data sheet 4147.

    Sizing It Into a Design

    10 uH sits in the middle of the range, and the trade at that point is explicit: 26 mOhm of DCR against 4.4 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1040-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products