Eaton DR1040-101-R Shielded Drum Core, 100 uH uH 225 mOhm
Eaton DR1040-101-R Shielded Drum Core, 100 uH uH 225 mOhm

Eaton DR1040-101-R Shielded Drum Core, 100 uH uH 225 mOhm

Share
Eaton DR1040-101-R: Shielded Drum Core Power Inductor, 100 uH, 1.25 A, DCR 225 mOhm.
    • Product Details
    • Download

    Eaton DR1040-101-R Shielded Drum Core, 100 uH uH 225 mOhm

    DR1040-101-R at a glance: shielded drum core inductor, 100 uH, 1.25 A Irms, 1.35 A Isat, DCR 225 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR1040-101-R
    Rated inductance100 uH ±20%
    Open circuit inductance (OCL)101 uH
    Irms (40 °C rise)1.25 A
    Isat1.35 A
    DCR typical @ 20 °C225 mOhm
    DCR maximum @ 20 °C304 mOhm
    K-factor (Bp-p = K x L x dI)1.9
    Package10.5 x 10.3 mm footprint, 4.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    Copper loss grows with the square of the current, so 225 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Isat is the peak current for approximately 35% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    The DR1040 sits between the 3.0 mm DR1030 and the 5.0 mm DR1050 on the same 10.5 x 10.3 mm pad. It exists so that a design can move up in current without redoing the land pattern - the footprint is identical across all three.

    • Typical applications: Server and desktop power supplies, graphics cards, point-of-load modules, portable electronics, printers and peripherals.
    • Same pad as DR1030 and DR1050, so a height change is a drop-in swap on an existing board - the electrical limits change, the layout does not.
    • Data sheet 4147.

    Putting It to Work

    At 100 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 225 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1040-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products