Eaton DR1040-150-R 3.6 A Saturation Shielded Inductor 15 uH
Eaton DR1040-150-R 3.6 A Saturation Shielded Inductor 15 uH

Eaton DR1040-150-R 3.6 A Saturation Shielded Inductor 15 uH

Share
Eaton DR1040-150-R: Shielded Drum Core Power Inductor, 15 uH, 3.1 A, DCR 37 mOhm.
    • Product Details
    • Download

    Eaton DR1040-150-R 3.6 A Saturation Shielded Inductor 15 uH

    DR1040-150-R at a glance: shielded drum core inductor, 15 uH, 3.1 A Irms, 3.6 A Isat, DCR 37 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR1040-150-R
    Rated inductance15 uH ±20%
    Open circuit inductance (OCL)14.9 uH
    Irms (40 °C rise)3.1 A
    Isat3.6 A
    DCR typical @ 20 °C37 mOhm
    DCR maximum @ 20 °C50 mOhm
    K-factor (Bp-p = K x L x dI)4.7
    Package10.5 x 10.3 mm footprint, 4.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    The DC resistance sets the efficiency floor. 37 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    The DR1040 sits between the 3.0 mm DR1030 and the 5.0 mm DR1050 on the same 10.5 x 10.3 mm pad. It exists so that a design can move up in current without redoing the land pattern - the footprint is identical across all three.

    • Typical applications: Server and desktop power supplies, graphics cards, point-of-load modules, portable electronics, printers and peripherals.
    • Same pad as DR1030 and DR1050, so a height change is a drop-in swap on an existing board - the electrical limits change, the layout does not.
    • Data sheet 4147.

    Sizing and Layout Notes

    15 uH sits in the middle of the range, and the trade at that point is explicit: 37 mOhm of DCR against 3.6 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1040-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message