Eaton DR1040-151-R 150 uH Shielded Power Inductor, 0.85 A
Eaton DR1040-151-R 150 uH Shielded Power Inductor, 0.85 A

Eaton DR1040-151-R 150 uH Shielded Power Inductor, 0.85 A

Share
Eaton DR1040-151-R: Shielded Drum Core Power Inductor, 150 uH, 0.85 A, DCR 356 mOhm.
    • Product Details
    • Download

    Eaton DR1040-151-R 150 uH Shielded Power Inductor, 0.85 A

    DR1040-151-R at a glance: shielded drum core inductor, 150 uH, 0.85 A Irms, 1.15 A Isat, DCR 356 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR1040-151-R
    Rated inductance150 uH ±20%
    Open circuit inductance (OCL)148 uH
    Irms (40 °C rise)0.85 A
    Isat1.15 A
    DCR typical @ 20 °C356 mOhm
    DCR maximum @ 20 °C430 mOhm
    K-factor (Bp-p = K x L x dI)1.6
    Package10.5 x 10.3 mm footprint, 4.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    The DC resistance sets the efficiency floor. 356 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 35% rolloff at +25 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    The DR1040 sits between the 3.0 mm DR1030 and the 5.0 mm DR1050 on the same 10.5 x 10.3 mm pad. It exists so that a design can move up in current without redoing the land pattern - the footprint is identical across all three.

    • Typical applications: Server and desktop power supplies, graphics cards, point-of-load modules, portable electronics, printers and peripherals.
    • Same pad as DR1030 and DR1050, so a height change is a drop-in swap on an existing board - the electrical limits change, the layout does not.
    • Data sheet 4147.

    Sizing and Layout Notes

    150 uH sits in the middle of the range, and the trade at that point is explicit: 356 mOhm of DCR against 1.15 A of saturation headroom.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1040-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message