Eaton DR1040-221-R Shielded Drum Core, 220 uH uH 530 mOhm
Eaton DR1040-221-R Shielded Drum Core, 220 uH uH 530 mOhm

Eaton DR1040-221-R Shielded Drum Core, 220 uH uH 530 mOhm

Share
Eaton DR1040-221-R: Shielded Drum Core Power Inductor, 220 uH, 0.7 A, DCR 530 mOhm.
    • Product Details
    • Download

    Eaton DR1040-221-R Shielded Drum Core, 220 uH uH 530 mOhm

    DR1040-221-R at a glance: shielded drum core inductor, 220 uH, 0.7 A Irms, 0.92 A Isat, DCR 530 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR1040-221-R
    Rated inductance220 uH ±20%
    Open circuit inductance (OCL)216 uH
    Irms (40 °C rise)0.7 A
    Isat0.92 A
    DCR typical @ 20 °C530 mOhm
    DCR maximum @ 20 °C640 mOhm
    K-factor (Bp-p = K x L x dI)1.3
    Package10.5 x 10.3 mm footprint, 4.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    At 530 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    Isat is the peak current for approximately 35% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    What This Family Is For

    The DR1040 sits between the 3.0 mm DR1030 and the 5.0 mm DR1050 on the same 10.5 x 10.3 mm pad. It exists so that a design can move up in current without redoing the land pattern - the footprint is identical across all three.

    • Typical applications: Server and desktop power supplies, graphics cards, point-of-load modules, portable electronics, printers and peripherals.
    • Same pad as DR1030 and DR1050, so a height change is a drop-in swap on an existing board - the electrical limits change, the layout does not.
    • Data sheet 4147.

    Sizing It Into a Design

    Choose 220 uH when the ripple target is at the high end of the design window: the DCR stays at 530 mOhm and the saturation limit at 0.92 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1040-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message