Eaton DR1050-100-R 4.6 A Saturation Shielded Inductor 10 uH
Eaton DR1050-100-R 4.6 A Saturation Shielded Inductor 10 uH

Eaton DR1050-100-R 4.6 A Saturation Shielded Inductor 10 uH

Share
Eaton DR1050-100-R: Shielded Drum Core Power Inductor, 10 uH, 4.8 A, DCR 18 mOhm.
    • Product Details
    • Download

    Eaton DR1050-100-R 4.6 A Saturation Shielded Inductor 10 uH

    DR1050-100-R at a glance: shielded drum core inductor, 10 uH, 4.8 A Irms, 4.6 A Isat, DCR 18 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR1050-100-R
    Rated inductance10 uH ±20%
    Open circuit inductance (OCL)10.1 uH
    Irms (40 °C rise)4.8 A
    Isat4.6 A
    DCR typical @ 20 °C18 mOhm
    DCR maximum @ 20 °C23 mOhm
    K-factor (Bp-p = K x L x dI)5.39
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    At 18 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    Isat is the peak current for approximately 35% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Putting It to Work

    Choose 10 uH when the ripple target is in the middle of the design window: the DCR stays at 18 mOhm and the saturation limit at 4.6 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products