Eaton DR1050-102-R 1000 uH Shielded Drum Core Inductor
Eaton DR1050-102-R 1000 uH Shielded Drum Core Inductor

Eaton DR1050-102-R 1000 uH Shielded Drum Core Inductor

Share
Eaton DR1050-102-R: Shielded Drum Core Power Inductor, 1000 uH, 0.43 A, DCR 1.53 ohm.
    • Product Details
    • Download

    Eaton DR1050-102-R 1000 uH Shielded Drum Core Inductor

    DR1050-102-R at a glance: shielded drum core inductor, 1000 uH, 0.43 A Irms, 0.48 A Isat, DCR 1528 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR1050-102-R
    Rated inductance1000 uH ±20%
    Open circuit inductance (OCL)1000 uH
    Irms (40 °C rise)0.43 A
    Isat0.48 A
    DCR typical @ 20 °C1528 mOhm
    DCR maximum @ 20 °C1950 mOhm
    K-factor (Bp-p = K x L x dI)0.54
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    Copper loss grows with the square of the current, so 1528 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Where This Series Fits

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Design Notes

    1000 uH is at the high end of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message