Eaton DR1050-221-R 220 uH Shielded Power Inductor, 1 A
Eaton DR1050-221-R 220 uH Shielded Power Inductor, 1 A

Eaton DR1050-221-R 220 uH Shielded Power Inductor, 1 A

Share
Eaton DR1050-221-R: Shielded Drum Core Power Inductor, 220 uH, 1 A, DCR 377 mOhm.
    • Product Details
    • Download

    Eaton DR1050-221-R 220 uH Shielded Power Inductor, 1 A

    DR1050-221-R at a glance: shielded drum core inductor, 220 uH, 1 A Irms, 0.98 A Isat, DCR 377 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR1050-221-R
    Rated inductance220 uH ±20%
    Open circuit inductance (OCL)222 uH
    Irms (40 °C rise)1 A
    Isat0.98 A
    DCR typical @ 20 °C377 mOhm
    DCR maximum @ 20 °C472 mOhm
    K-factor (Bp-p = K x L x dI)1.15
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    The DC resistance sets the efficiency floor. 377 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is the peak current for approximately 35% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Series Positioning

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Sizing and Layout Notes

    Choose 220 uH when the ripple target is in the middle of the design window: the DCR stays at 377 mOhm and the saturation limit at 0.98 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products