Eaton DR1050-270-R 27 uH Shielded Drum Core Inductor
Eaton DR1050-270-R 27 uH Shielded Drum Core Inductor

Eaton DR1050-270-R 27 uH Shielded Drum Core Inductor

Share
Eaton DR1050-270-R: Shielded Drum Core Power Inductor, 27 uH, 2.82 A, DCR 43 mOhm.
    • Product Details
    • Download

    Eaton DR1050-270-R 27 uH Shielded Drum Core Inductor

    DR1050-270-R at a glance: shielded drum core inductor, 27 uH, 2.82 A Irms, 2.8 A Isat, DCR 43 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR1050-270-R
    Rated inductance27 uH ±20%
    Open circuit inductance (OCL)26.9 uH
    Irms (40 °C rise)2.82 A
    Isat2.8 A
    DCR typical @ 20 °C43 mOhm
    DCR maximum @ 20 °C53 mOhm
    K-factor (Bp-p = K x L x dI)3.3
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    DCR 43 mOhm is the conduction loss: at the rated current it dissipates about 0.34 W, and that heat has to leave through the terminals and the board.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Series Positioning

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Sizing and Layout Notes

    At 27 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 43 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products