Eaton DR1050-2R2-R Shielded Drum Core, 2.2 uH uH 5.6 mOhm
Eaton DR1050-2R2-R Shielded Drum Core, 2.2 uH uH 5.6 mOhm

Eaton DR1050-2R2-R Shielded Drum Core, 2.2 uH uH 5.6 mOhm

Share
Eaton DR1050-2R2-R: Shielded Drum Core Power Inductor, 2.2 uH, 7.52 A, DCR 5.6 mOhm.
    • Product Details
    • Download

    Eaton DR1050-2R2-R Shielded Drum Core, 2.2 uH uH 5.6 mOhm

    DR1050-2R2-R at a glance: shielded drum core inductor, 2.2 uH, 7.52 A Irms, 9.3 A Isat, DCR 5.6 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR1050-2R2-R
    Rated inductance2.2 uH ±20%
    Open circuit inductance (OCL)2.27 uH
    Irms (40 °C rise)7.52 A
    Isat9.3 A
    DCR typical @ 20 °C5.6 mOhm
    DCR maximum @ 20 °C6.8 mOhm
    K-factor (Bp-p = K x L x dI)11.4
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    Copper loss grows with the square of the current, so 5.6 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Sizing It Into a Design

    At 2.2 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 5.6 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products