Eaton DR1050-390-R 39 uH Shielded Drum Core Inductor
Eaton DR1050-390-R 39 uH Shielded Drum Core Inductor

Eaton DR1050-390-R 39 uH Shielded Drum Core Inductor

Share
Eaton DR1050-390-R: Shielded Drum Core Power Inductor, 39 uH, 2.35 A, DCR 61 mOhm.
    • Product Details
    • Download

    Eaton DR1050-390-R 39 uH Shielded Drum Core Inductor

    DR1050-390-R at a glance: shielded drum core inductor, 39 uH, 2.35 A Irms, 2.35 A Isat, DCR 61 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR1050-390-R
    Rated inductance39 uH ±20%
    Open circuit inductance (OCL)38.3 uH
    Irms (40 °C rise)2.35 A
    Isat2.35 A
    DCR typical @ 20 °C61 mOhm
    DCR maximum @ 20 °C76 mOhm
    K-factor (Bp-p = K x L x dI)2.77
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    DCR 61 mOhm is the conduction loss: at the rated current it dissipates about 0.34 W, and that heat has to leave through the terminals and the board.

    Isat is the peak current for approximately 35% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    What This Family Is For

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Sizing and Layout Notes

    Choose 39 uH when the ripple target is in the middle of the design window: the DCR stays at 61 mOhm and the saturation limit at 2.35 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message