Eaton DR1050-470-R 2.1 A Saturation Shielded Inductor 47 uH
Eaton DR1050-470-R 2.1 A Saturation Shielded Inductor 47 uH

Eaton DR1050-470-R 2.1 A Saturation Shielded Inductor 47 uH

Share
Eaton DR1050-470-R: Shielded Drum Core Power Inductor, 47 uH, 2.06 A, DCR 89 mOhm.
    • Product Details
    • Download

    Eaton DR1050-470-R 2.1 A Saturation Shielded Inductor 47 uH

    DR1050-470-R at a glance: shielded drum core inductor, 47 uH, 2.06 A Irms, 2.1 A Isat, DCR 89 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR1050-470-R
    Rated inductance47 uH ±20%
    Open circuit inductance (OCL)47.1 uH
    Irms (40 °C rise)2.06 A
    Isat2.1 A
    DCR typical @ 20 °C89 mOhm
    DCR maximum @ 20 °C111 mOhm
    K-factor (Bp-p = K x L x dI)2.5
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    At 89 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Positioning in the Range

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Sizing It Into a Design

    Choose 47 uH when the ripple target is in the middle of the design window: the DCR stays at 89 mOhm and the saturation limit at 2.1 A leaves the transient room it needs.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products