Eaton DR1050-471-R 470 uH Shielded Power Inductor, 0.64 A
Eaton DR1050-471-R 470 uH Shielded Power Inductor, 0.64 A

Eaton DR1050-471-R 470 uH Shielded Power Inductor, 0.64 A

Share
Eaton DR1050-471-R: Shielded Drum Core Power Inductor, 470 uH, 0.64 A, DCR 855 mOhm.
    • Product Details
    • Download

    Eaton DR1050-471-R 470 uH Shielded Power Inductor, 0.64 A

    DR1050-471-R at a glance: shielded drum core inductor, 470 uH, 0.64 A Irms, 0.62 A Isat, DCR 855 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR1050-471-R
    Rated inductance470 uH ±20%
    Open circuit inductance (OCL)481 uH
    Irms (40 °C rise)0.64 A
    Isat0.62 A
    DCR typical @ 20 °C855 mOhm
    DCR maximum @ 20 °C1069 mOhm
    K-factor (Bp-p = K x L x dI)0.78
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    The DC resistance sets the efficiency floor. 855 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 35% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Positioning in the Range

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Design Notes

    At 470 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 855 mOhm DCR - more turns, thinner wire, more resistance.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products