Eaton DR1050-4R7-R 4.7 uH Shielded Drum Core Inductor
Eaton DR1050-4R7-R 4.7 uH Shielded Drum Core Inductor

Eaton DR1050-4R7-R 4.7 uH Shielded Drum Core Inductor

Share
Eaton DR1050-4R7-R: Shielded Drum Core Power Inductor, 4.7 uH, 6.13 A, DCR 10 mOhm.
    • Product Details
    • Download

    Eaton DR1050-4R7-R 4.7 uH Shielded Drum Core Inductor

    DR1050-4R7-R at a glance: shielded drum core inductor, 4.7 uH, 6.13 A Irms, 6.7 A Isat, DCR 10 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR1050-4R7-R
    Rated inductance4.7 uH ±20%
    Open circuit inductance (OCL)4.43 uH
    Irms (40 °C rise)6.13 A
    Isat6.7 A
    DCR typical @ 20 °C10 mOhm
    DCR maximum @ 20 °C12 mOhm
    K-factor (Bp-p = K x L x dI)7.87
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    DCR 10 mOhm is the conduction loss: at the rated current it dissipates about 0.38 W, and that heat has to leave through the terminals and the board.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 35% rolloff at +25 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Series Positioning

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Sizing and Layout Notes

    4.7 uH sits in the middle of the range, and the trade at that point is explicit: 10 mOhm of DCR against 6.7 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products