Eaton DR1050-821-R Shielded Drum Core, 820 uH uH 1185 mOhm
Eaton DR1050-821-R Shielded Drum Core, 820 uH uH 1185 mOhm

Eaton DR1050-821-R Shielded Drum Core, 820 uH uH 1185 mOhm

Share
Eaton DR1050-821-R: Shielded Drum Core Power Inductor, 820 uH, 0.54 A, DCR 1.19 ohm.
    • Product Details
    • Download

    Eaton DR1050-821-R Shielded Drum Core, 820 uH uH 1185 mOhm

    DR1050-821-R at a glance: shielded drum core inductor, 820 uH, 0.54 A Irms, 0.5 A Isat, DCR 1185 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR1050-821-R
    Rated inductance820 uH ±20%
    Open circuit inductance (OCL)819 uH
    Irms (40 °C rise)0.54 A
    Isat0.5 A
    DCR typical @ 20 °C1185 mOhm
    DCR maximum @ 20 °C1481 mOhm
    K-factor (Bp-p = K x L x dI)0.6
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    At 1185 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 35% rolloff at +25 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Design Notes

    At 820 uH this part is at the high end of the family. The winding that produces that inductance is also what sets the 1185 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products