Eaton DR1050-R80-R 0.8 uH Shielded Power Inductor, 9.7 A
Eaton DR1050-R80-R 0.8 uH Shielded Power Inductor, 9.7 A

Eaton DR1050-R80-R 0.8 uH Shielded Power Inductor, 9.7 A

Share
Eaton DR1050-R80-R: Shielded Drum Core Power Inductor, 0.8 uH, 9.7 A, DCR 3.2 mOhm.
    • Product Details
    • Download

    Eaton DR1050-R80-R 0.8 uH Shielded Power Inductor, 9.7 A

    DR1050-R80-R at a glance: shielded drum core inductor, 0.8 uH, 9.7 A Irms, 13.5 A Isat, DCR 3.2 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR1050-R80-R
    Rated inductance0.8 uH ±20%
    Open circuit inductance (OCL)0.7 uH
    Irms (40 °C rise)9.7 A
    Isat13.5 A
    DCR typical @ 20 °C3.2 mOhm
    DCR maximum @ 20 °C4 mOhm
    K-factor (Bp-p = K x L x dI)20.5
    Package10.5 x 10.3 mm footprint, 5.0 mm height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    DCR 3.2 mOhm is the conduction loss: at the rated current it dissipates about 0.30 W, and that heat has to leave through the terminals and the board.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 35% rolloff at +25 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Where This Series Fits

    The DR1050 is the tallest of the 10.5 x 10.3 mm family, and the one that reaches 1000 uH. Where the 3.0 mm part runs out of copper, the 5.0 mm body keeps the winding cool enough to hold its rating.

    • Typical applications: Server and desktop power supplies, LED/LCD backlighting, graphics cards, point-of-load modules, printers and peripherals.
    • The extra height buys current, not saturation - check Isat separately, because a taller core does not automatically mean a higher flux limit.
    • Data sheet 4139.

    Sizing It Into a Design

    At 0.8 uH this part is at the low end of the family. The winding that produces that inductance is also what sets the 3.2 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr1050-shielded-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message