Eaton DR124-101-R - 100 uH 1.5 A Shielded Inductor
Eaton DR124-101-R - 100 uH 1.5 A Shielded Inductor

Eaton DR124-101-R - 100 uH 1.5 A Shielded Inductor

Share
Eaton DR124-101-R: Low Profile Shielded Drum Core Inductor, 100 uH, 1.5 A, DCR 256.67 mOhm.
    • Product Details
    • Download

    Eaton DR124-101-R - 100 uH 1.5 A Shielded Inductor

    DR124-101-R at a glance: shielded drum core inductor, 100 uH, 1.5 A Irms, 1.79 A Isat, DCR 257 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR124-101-R
    Rated inductance100 uH ±20%
    Open circuit inductance (OCL)95.1 uH
    Irms (40 °C rise)1.5 A
    Isat1.79 A
    DCR typical @ 20 °C257 mOhm
    DCR maximum @ 20 °C308 mOhm
    K-factor (Bp-p = K x L x dI)1.17
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    DCR 257 mOhm is the conduction loss: at the rated current it dissipates about 0.58 W, and that heat has to leave through the terminals and the board.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 25% rolloff at +25 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Positioning in the Range

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Sizing and Layout Notes

    At 100 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 257 mOhm DCR - more turns, thinner wire, more resistance.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products