Eaton DR124-1R5-R 1.5 uH Shielded Drum Core Inductor
Eaton DR124-1R5-R 1.5 uH Shielded Drum Core Inductor

Eaton DR124-1R5-R 1.5 uH Shielded Drum Core Inductor

Share
Eaton DR124-1R5-R: Low Profile Shielded Drum Core Inductor, 1.5 uH, 11.1 A, DCR 4.75 mOhm.
    • Product Details
    • Download

    Eaton DR124-1R5-R 1.5 uH Shielded Drum Core Inductor

    DR124-1R5-R at a glance: shielded drum core inductor, 1.5 uH, 11.1 A Irms, 14 A Isat, DCR 4.75 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR124-1R5-R
    Rated inductance1.5 uH ±20%
    Open circuit inductance (OCL)1.37 uH
    Irms (40 °C rise)11.1 A
    Isat14 A
    DCR typical @ 20 °C4.75 mOhm
    DCR maximum @ 20 °C5.7 mOhm
    K-factor (Bp-p = K x L x dI)9.73
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    The DC resistance sets the efficiency floor. 4.75 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is the peak current for approximately 25% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Sizing It Into a Design

    At 1.5 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 4.75 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message