Eaton DR124-270-R 3.44 A Saturation Shielded Inductor 27 uH
Eaton DR124-270-R 3.44 A Saturation Shielded Inductor 27 uH

Eaton DR124-270-R 3.44 A Saturation Shielded Inductor 27 uH

Share
Eaton DR124-270-R: Low Profile Shielded Drum Core Inductor, 27 uH, 2.8 A, DCR 66.67 mOhm.
    • Product Details
    • Download

    Eaton DR124-270-R 3.44 A Saturation Shielded Inductor 27 uH

    DR124-270-R at a glance: shielded drum core inductor, 27 uH, 2.8 A Irms, 3.44 A Isat, DCR 66.7 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR124-270-R
    Rated inductance27 uH ±20%
    Open circuit inductance (OCL)25.7 uH
    Irms (40 °C rise)2.8 A
    Isat3.44 A
    DCR typical @ 20 °C66.7 mOhm
    DCR maximum @ 20 °C80 mOhm
    K-factor (Bp-p = K x L x dI)2.24
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    At 66.7 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 25% rolloff at +25 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    What This Family Is For

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Sizing It Into a Design

    Choose 27 uH when the ripple target is in the middle of the design window: the DCR stays at 66.7 mOhm and the saturation limit at 3.44 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products