Eaton DR124-271-R 270 uH Shielded Power Inductor, 0.88 A
Eaton DR124-271-R 270 uH Shielded Power Inductor, 0.88 A

Eaton DR124-271-R 270 uH Shielded Power Inductor, 0.88 A

Share
Eaton DR124-271-R: Low Profile Shielded Drum Core Inductor, 270 uH, 0.88 A, DCR 725 mOhm.
    • Product Details
    • Download

    Eaton DR124-271-R 270 uH Shielded Power Inductor, 0.88 A

    DR124-271-R at a glance: shielded drum core inductor, 270 uH, 0.88 A Irms, 1.09 A Isat, DCR 725 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR124-271-R
    Rated inductance270 uH ±20%
    Open circuit inductance (OCL)256 uH
    Irms (40 °C rise)0.88 A
    Isat1.09 A
    DCR typical @ 20 °C725 mOhm
    DCR maximum @ 20 °C870 mOhm
    K-factor (Bp-p = K x L x dI)0.71
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    Copper loss grows with the square of the current, so 725 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 25% rolloff at +25 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Series Positioning

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Sizing and Layout Notes

    At 270 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 725 mOhm DCR - more turns, thinner wire, more resistance.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products