Eaton DR124-2R2-R 2.2 uH Shielded Drum Core Inductor
Eaton DR124-2R2-R 2.2 uH Shielded Drum Core Inductor

Eaton DR124-2R2-R 2.2 uH Shielded Drum Core Inductor

Share
Eaton DR124-2R2-R: Low Profile Shielded Drum Core Inductor, 2.2 uH, 9.1 A, DCR 5.92 mOhm.
    • Product Details
    • Download

    Eaton DR124-2R2-R 2.2 uH Shielded Drum Core Inductor

    DR124-2R2-R at a glance: shielded drum core inductor, 2.2 uH, 9.1 A Irms, 11.4 A Isat, DCR 5.92 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR124-2R2-R
    Rated inductance2.2 uH ±20%
    Open circuit inductance (OCL)2.04 uH
    Irms (40 °C rise)9.1 A
    Isat11.4 A
    DCR typical @ 20 °C5.92 mOhm
    DCR maximum @ 20 °C7.1 mOhm
    K-factor (Bp-p = K x L x dI)7.96
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    The DC resistance sets the efficiency floor. 5.92 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 25% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Series Positioning

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Design Notes

    2.2 uH sits in the middle of the range, and the trade at that point is explicit: 5.92 mOhm of DCR against 11.4 A of saturation headroom.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message