Eaton DR124-331-R Shielded Drum Core, 330 uH uH 825 mOhm
Eaton DR124-331-R Shielded Drum Core, 330 uH uH 825 mOhm

Eaton DR124-331-R Shielded Drum Core, 330 uH uH 825 mOhm

Share
Eaton DR124-331-R: Low Profile Shielded Drum Core Inductor, 330 uH, 0.83 A, DCR 825 mOhm.
    • Product Details
    • Download

    Eaton DR124-331-R Shielded Drum Core, 330 uH uH 825 mOhm

    DR124-331-R at a glance: shielded drum core inductor, 330 uH, 0.83 A Irms, 0.92 A Isat, DCR 825 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR124-331-R
    Rated inductance330 uH ±20%
    Open circuit inductance (OCL)327 uH
    Irms (40 °C rise)0.83 A
    Isat0.92 A
    DCR typical @ 20 °C825 mOhm
    DCR maximum @ 20 °C990 mOhm
    K-factor (Bp-p = K x L x dI)0.63
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    The DC resistance sets the efficiency floor. 825 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 25% rolloff at +25 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Positioning in the Range

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Design Notes

    330 uH sits in the middle of the range, and the trade at that point is explicit: 825 mOhm of DCR against 0.92 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products