Eaton DR124-390-R 2.85 A Saturation Shielded Inductor 39 uH
Eaton DR124-390-R 2.85 A Saturation Shielded Inductor 39 uH

Eaton DR124-390-R 2.85 A Saturation Shielded Inductor 39 uH

Share
Eaton DR124-390-R: Low Profile Shielded Drum Core Inductor, 39 uH, 2.3 A, DCR 110 mOhm.
    • Product Details
    • Download

    Eaton DR124-390-R 2.85 A Saturation Shielded Inductor 39 uH

    DR124-390-R at a glance: shielded drum core inductor, 39 uH, 2.3 A Irms, 2.85 A Isat, DCR 110 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR124-390-R
    Rated inductance39 uH ±20%
    Open circuit inductance (OCL)37.3 uH
    Irms (40 °C rise)2.3 A
    Isat2.85 A
    DCR typical @ 20 °C110 mOhm
    DCR maximum @ 20 °C132 mOhm
    K-factor (Bp-p = K x L x dI)1.86
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    The DC resistance sets the efficiency floor. 110 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Saturation degrades with temperature on ferrite. Isat is the peak current for approximately 25% rolloff at +25 °C, and the hot value is the one that matters under a hood or inside a sealed enclosure.

    Positioning in the Range

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Sizing It Into a Design

    Choose 39 uH when the ripple target is in the middle of the design window: the DCR stays at 110 mOhm and the saturation limit at 2.85 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message