Eaton DR124-470-R 47 uH Shielded Drum Core Inductor
Eaton DR124-470-R 47 uH Shielded Drum Core Inductor

Eaton DR124-470-R 47 uH Shielded Drum Core Inductor

Share
Eaton DR124-470-R: Low Profile Shielded Drum Core Inductor, 47 uH, 2.2 A, DCR 124.66 mOhm.
    • Product Details
    • Download

    Eaton DR124-470-R 47 uH Shielded Drum Core Inductor

    DR124-470-R at a glance: shielded drum core inductor, 47 uH, 2.2 A Irms, 2.63 A Isat, DCR 125 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR124-470-R
    Rated inductance47 uH ±20%
    Open circuit inductance (OCL)44 uH
    Irms (40 °C rise)2.2 A
    Isat2.63 A
    DCR typical @ 20 °C125 mOhm
    DCR maximum @ 20 °C150 mOhm
    K-factor (Bp-p = K x L x dI)1.72
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    DCR 125 mOhm is the conduction loss: at the rated current it dissipates about 0.60 W, and that heat has to leave through the terminals and the board.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 25% rolloff at +25 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    What This Family Is For

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Putting It to Work

    Choose 47 uH when the ripple target is in the middle of the design window: the DCR stays at 125 mOhm and the saturation limit at 2.63 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products