Eaton DR124-471-R - 470 uH 0.68 A Shielded Inductor
Eaton DR124-471-R - 470 uH 0.68 A Shielded Inductor

Eaton DR124-471-R - 470 uH 0.68 A Shielded Inductor

Share
Eaton DR124-471-R: Low Profile Shielded Drum Core Inductor, 470 uH, 0.68 A, DCR 1.24 ohm.
    • Product Details
    • Download

    Eaton DR124-471-R - 470 uH 0.68 A Shielded Inductor

    DR124-471-R at a glance: shielded drum core inductor, 470 uH, 0.68 A Irms, 0.74 A Isat, DCR 1242 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR124-471-R
    Rated inductance470 uH ±20%
    Open circuit inductance (OCL)460 uH
    Irms (40 °C rise)0.68 A
    Isat0.74 A
    DCR typical @ 20 °C1242 mOhm
    DCR maximum @ 20 °C1491 mOhm
    K-factor (Bp-p = K x L x dI)0.53
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    DCR 1242 mOhm is the conduction loss: at the rated current it dissipates about 0.57 W, and that heat has to leave through the terminals and the board.

    Isat is the peak current for approximately 25% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Series Positioning

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Putting It to Work

    At 470 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 1242 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message