Eaton DR124-4R7-R Shielded Drum Core, 4.7 uH uH 13.5 mOhm
Eaton DR124-4R7-R Shielded Drum Core, 4.7 uH uH 13.5 mOhm

Eaton DR124-4R7-R Shielded Drum Core, 4.7 uH uH 13.5 mOhm

Share
Eaton DR124-4R7-R: Low Profile Shielded Drum Core Inductor, 4.7 uH, 6.5 A, DCR 13.5 mOhm.
    • Product Details
    • Download

    Eaton DR124-4R7-R Shielded Drum Core, 4.7 uH uH 13.5 mOhm

    DR124-4R7-R at a glance: shielded drum core inductor, 4.7 uH, 6.5 A Irms, 7.65 A Isat, DCR 13.5 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR124-4R7-R
    Rated inductance4.7 uH ±20%
    Open circuit inductance (OCL)4.88 uH
    Irms (40 °C rise)6.5 A
    Isat7.65 A
    DCR typical @ 20 °C13.5 mOhm
    DCR maximum @ 20 °C16.2 mOhm
    K-factor (Bp-p = K x L x dI)5.15
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    The DC resistance sets the efficiency floor. 13.5 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is the peak current for approximately 25% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Design Notes

    4.7 uH sits in the middle of the range, and the trade at that point is explicit: 13.5 mOhm of DCR against 7.65 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message