Eaton DR124-820-R Shielded Drum Core, 82 uH uH 213 mOhm
Eaton DR124-820-R Shielded Drum Core, 82 uH uH 213 mOhm

Eaton DR124-820-R Shielded Drum Core, 82 uH uH 213 mOhm

Share
Eaton DR124-820-R: Low Profile Shielded Drum Core Inductor, 82 uH, 1.7 A, DCR 212.72 mOhm.
    • Product Details
    • Download

    Eaton DR124-820-R Shielded Drum Core, 82 uH uH 213 mOhm

    DR124-820-R at a glance: shielded drum core inductor, 82 uH, 1.7 A Irms, 1.94 A Isat, DCR 213 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR124-820-R
    Rated inductance82 uH ±20%
    Open circuit inductance (OCL)80.5 uH
    Irms (40 °C rise)1.7 A
    Isat1.94 A
    DCR typical @ 20 °C213 mOhm
    DCR maximum @ 20 °C255 mOhm
    K-factor (Bp-p = K x L x dI)1.27
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    DCR 213 mOhm is the conduction loss: at the rated current it dissipates about 0.61 W, and that heat has to leave through the terminals and the board.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 25% rolloff at +25 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Series Positioning

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Sizing and Layout Notes

    At 82 uH this part is in the middle of the family. The winding that produces that inductance is also what sets the 213 mOhm DCR - more turns, thinner wire, more resistance.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products