Eaton DR124-821-R 0.62 A Saturation Shielded Inductor 820 uH
Eaton DR124-821-R 0.62 A Saturation Shielded Inductor 820 uH

Eaton DR124-821-R 0.62 A Saturation Shielded Inductor 820 uH

Share
Eaton DR124-821-R: Low Profile Shielded Drum Core Inductor, 820 uH, 0.53 A, DCR 2.11 ohm.
    • Product Details
    • Download

    Eaton DR124-821-R 0.62 A Saturation Shielded Inductor 820 uH

    DR124-821-R at a glance: shielded drum core inductor, 820 uH, 0.53 A Irms, 0.62 A Isat, DCR 2109 mOhm.

    Ratings at a Glance

    ParameterValue
    Orderable part numberDR124-821-R
    Rated inductance820 uH ±20%
    Open circuit inductance (OCL)825 uH
    Irms (40 °C rise)0.53 A
    Isat0.62 A
    DCR typical @ 20 °C2109 mOhm
    DCR maximum @ 20 °C2351 mOhm
    K-factor (Bp-p = K x L x dI)0.4
    Package12.5 x 12.5 x 4.5 mm
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    The DC resistance sets the efficiency floor. 2109 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is the peak current for approximately 25% rolloff at +25 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Where This Series Fits

    The DR124 is the 4.5 mm low-profile member of the 12.5 mm DR family: 0.47 uH to 1000 uH in a body that stays under 5 mm, with current up to 24.4 A. It is the part you reach for when the board is thin but the rail is not small.

    • Typical applications: Notebook power, LCD panels, desktop and servers, DVD players, DC-DC converters, buck/boost/forward/resonant topologies, noise filtering.
    • Frequency range is quoted to 1 MHz - above that the core loss climbs faster than the ripple benefit, and the DCR is no longer the dominant term.
    • Data sheet 4141.

    Design Notes

    Choose 820 uH when the ripple target is at the high end of the design window: the DCR stays at 2109 mOhm and the saturation limit at 0.62 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Is Isat a thermal limit?
    No. Isat is where the core starts to saturate and the inductance falls by the stated percentage. Temperature is governed by Irms and the board, separately.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr124-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products