Eaton DR125-102-R Shielded Drum Core, 1000 uH uH 1690 mOhm
Eaton DR125-102-R Shielded Drum Core, 1000 uH uH 1690 mOhm

Eaton DR125-102-R Shielded Drum Core, 1000 uH uH 1690 mOhm

Share
Eaton DR125-102-R: Shielded Drum Core Power Inductor, 1000 uH, 0.57 A, DCR 1.69 ohm.
    • Product Details
    • Download

    Eaton DR125-102-R Shielded Drum Core, 1000 uH uH 1690 mOhm

    DR125-102-R at a glance: shielded drum core inductor, 1000 uH, 0.57 A Irms, 0.7 A Isat, DCR 1690 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR125-102-R
    Rated inductance1000 uH ±20%
    Open circuit inductance (OCL)1008 uH
    Irms (40 °C rise)0.57 A
    Isat0.7 A
    DCR typical @ 20 °C1690 mOhm
    Volt-microsecond rating149 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    Copper loss grows with the square of the current, so 1690 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Positioning in the Range

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Design Notes

    Choose 1000 uH when the ripple target is at the high end of the design window: the DCR stays at 1690 mOhm and the saturation limit at 0.7 A leaves the transient room it needs.

    Thermal design is not optional here. The rated current assumes a 40 °C rise with the part in free air on a stated pad; inside a closed box, on a thin board, next to a hot IC, that assumption is gone.

    Frequently Asked Questions

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products