Eaton DR125-1R0-R - 1 uH 15 A Shielded Inductor
Eaton DR125-1R0-R - 1 uH 15 A Shielded Inductor

Eaton DR125-1R0-R - 1 uH 15 A Shielded Inductor

Share
Eaton DR125-1R0-R: Shielded Drum Core Power Inductor, 1 uH, 15 A, DCR 2.4 mOhm.
    • Product Details
    • Download

    Eaton DR125-1R0-R - 1 uH 15 A Shielded Inductor

    DR125-1R0-R at a glance: shielded drum core inductor, 1 uH, 15 A Irms, 23.6 A Isat, DCR 2.4 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR125-1R0-R
    Rated inductance1 uH ±20%
    Open circuit inductance (OCL)0.89 uH
    Irms (40 °C rise)15 A
    Isat23.6 A
    DCR typical @ 20 °C2.4 mOhm
    Volt-microsecond rating4.43 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    Reading the Data Sheet

    Every part on this page is a shielded drum core: a winding on a ferrite bobbin, capped by a ferrite shield. The construction sets both the inductance and the saturation behaviour, and it is why the same footprint can cover two decades of inductance without changing the land pattern.

    Copper loss grows with the square of the current, so 2.4 mOhm matters most at full load. At half the rated current the winding loss drops to a quarter - which is why the part looks oversized for a light-load profile.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 30% rolloff at +20 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    Positioning in the Range

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Sizing and Layout Notes

    Choose 1 uH when the ripple target is in the middle of the design window: the DCR stays at 2.4 mOhm and the saturation limit at 23.6 A leaves the transient room it needs.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products