Eaton DR125-1R5-R Shielded Drum Core, 1.5 uH uH 2.9 mOhm
Eaton DR125-1R5-R Shielded Drum Core, 1.5 uH uH 2.9 mOhm

Eaton DR125-1R5-R Shielded Drum Core, 1.5 uH uH 2.9 mOhm

Share
Eaton DR125-1R5-R: Shielded Drum Core Power Inductor, 1.5 uH, 13.8 A, DCR 2.9 mOhm.
    • Product Details
    • Download

    Eaton DR125-1R5-R Shielded Drum Core, 1.5 uH uH 2.9 mOhm

    DR125-1R5-R at a glance: shielded drum core inductor, 1.5 uH, 13.8 A Irms, 18.3 A Isat, DCR 2.9 mOhm.

    Specification Table

    ParameterValue
    Orderable part numberDR125-1R5-R
    Rated inductance1.5 uH ±20%
    Open circuit inductance (OCL)1.48 uH
    Irms (40 °C rise)13.8 A
    Isat18.3 A
    DCR typical @ 20 °C2.9 mOhm
    Volt-microsecond rating5.7 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    The Figures Explained

    The drum core is the workhorse of DC-DC magnetics. It is cheap to build, it saturates in a predictable way, and with a ferrite shield over the winding it can be placed within a few millimetres of an IC without the field coupling into the die.

    DCR 2.9 mOhm is the conduction loss: at the rated current it dissipates about 0.55 W, and that heat has to leave through the terminals and the board.

    The saturation current is measured at a defined roll-off, and Eaton states the percentage on the data sheet: Isat is the peak current for approximately 30% rolloff at +20 °C. Read the number with the percentage in hand, because "saturation" means different things at 25% and at 40%.

    Series Positioning

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Sizing and Layout Notes

    1.5 uH is in the middle of what this series covers. Moving up in inductance costs DCR and saturation current; moving down buys both, at the price of ripple.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    What is the difference between OCL and rated inductance?
    OCL is measured at zero DC bias. The rated inductance is the value the part still has at its rated current, and that is what the ripple calculation needs.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message