Eaton DR125-3R3-R 12.7 A Saturation Shielded Inductor 3.3 uH
Eaton DR125-3R3-R 12.7 A Saturation Shielded Inductor 3.3 uH

Eaton DR125-3R3-R 12.7 A Saturation Shielded Inductor 3.3 uH

Share
Eaton DR125-3R3-R: Shielded Drum Core Power Inductor, 3.3 uH, 9.26 A, DCR 6.3 mOhm.
    • Product Details
    • Download

    Eaton DR125-3R3-R 12.7 A Saturation Shielded Inductor 3.3 uH

    DR125-3R3-R at a glance: shielded drum core inductor, 3.3 uH, 9.26 A Irms, 12.7 A Isat, DCR 6.3 mOhm.

    Electrical Specifications

    ParameterValue
    Orderable part numberDR125-3R3-R
    Rated inductance3.3 uH ±20%
    Open circuit inductance (OCL)3.08 uH
    Irms (40 °C rise)9.26 A
    Isat12.7 A
    DCR typical @ 20 °C6.3 mOhm
    Volt-microsecond rating8.23 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    The DC resistance sets the efficiency floor. 6.3 mOhm at 20 °C rises by roughly a third at 100 °C in copper, so the loss at the hot corner is the number to budget with.

    Isat is the peak current for approximately 30% rolloff at +20 °C. In a buck converter the inductor current peaks at the top of the ripple, so the peak - not the average - is the number that has to stay below Isat with margin for the transient.

    Positioning in the Range

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Sizing It Into a Design

    3.3 uH sits in the middle of the range, and the trade at that point is explicit: 6.3 mOhm of DCR against 12.7 A of saturation headroom.

    Efficiency is set by where you sit on the loss curve, and the curve moves with switching frequency. A part that is excellent at 300 kHz can be mediocre at 1 MHz with the same current, because the core loss term takes over.

    Frequently Asked Questions

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Why does the DCR have a typical and a maximum?
    Winding resistance varies with wire tolerance and termination. The maximum is the guaranteed limit and the one to use for a loss budget that has to hold in production.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message

    Shenzhen Gaorunxin Technology Co., Ltd

    Related Products