Eaton DR125-470-R 47 uH Shielded Power Inductor, 2.71 A
Eaton DR125-470-R 47 uH Shielded Power Inductor, 2.71 A

Eaton DR125-470-R 47 uH Shielded Power Inductor, 2.71 A

Share
Eaton DR125-470-R: Shielded Drum Core Power Inductor, 47 uH, 2.71 A, DCR 74 mOhm.
    • Product Details
    • Download

    Eaton DR125-470-R 47 uH Shielded Power Inductor, 2.71 A

    DR125-470-R at a glance: shielded drum core inductor, 47 uH, 2.71 A Irms, 3.24 A Isat, DCR 74 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR125-470-R
    Rated inductance47 uH ±20%
    Open circuit inductance (OCL)47.5 uH
    Irms (40 °C rise)2.71 A
    Isat3.24 A
    DCR typical @ 20 °C74 mOhm
    Volt-microsecond rating32.3 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    What the Numbers Mean

    A drum core inductor is a coil wound on a bobbin inside a ferrite pot, and the pot is what makes it usable on a switching board: the field stays inside the core instead of spraying across the PCB. That shielding is the difference between a rail that passes emissions and one that needs another filter stage.

    DCR 74 mOhm is the conduction loss: at the rated current it dissipates about 0.54 W, and that heat has to leave through the terminals and the board.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 30% rolloff at +20 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Putting It to Work

    Choose 47 uH when the ripple target is in the middle of the design window: the DCR stays at 74 mOhm and the saturation limit at 3.24 A leaves the transient room it needs.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    How is it mounted?
    Surface mount, reflow compatible and J-STD-020 compliant. The pad layout on the data sheet is the one the ratings were measured on.

    What is the K-factor for?
    It converts the peak-to-peak ripple into a flux swing: Bp-p = K x L x dI, with Bp-p in mT and L in uH. That flux swing is what you enter on the core loss graph.

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message