Eaton DR125-472-R - 4700 uH 0.27 A Shielded Inductor
Eaton DR125-472-R - 4700 uH 0.27 A Shielded Inductor

Eaton DR125-472-R - 4700 uH 0.27 A Shielded Inductor

Share
Eaton DR125-472-R: Shielded Drum Core Power Inductor, 4700 uH, 0.27 A, DCR 7.53 ohm.
    • Product Details
    • Download

    Eaton DR125-472-R - 4700 uH 0.27 A Shielded Inductor

    DR125-472-R at a glance: shielded drum core inductor, 4700 uH, 0.27 A Irms, 0.32 A Isat, DCR 7530 mOhm.

    Key Specifications

    ParameterValue
    Orderable part numberDR125-472-R
    Rated inductance4700 uH ±20%
    Open circuit inductance (OCL)4720 uH
    Irms (40 °C rise)0.27 A
    Isat0.32 A
    DCR typical @ 20 °C7530 mOhm
    Volt-microsecond rating322 V-us
    Package12.5 x 12.5 mm footprint, 6.0 mm max height
    MountingSurface mount
    Operating temperature-40 °C to +125 °C
    QualificationCommercial grade
    RoHSCompliant (-R suffix)

    How to Read These Ratings

    This is a surface-mount drum core with a ferrite shield. The winding sits in a pot core so the flux path closes through ferrite rather than through air, which raises the inductance for a given winding and keeps the radiated field small enough to sit next to a sensitive node.

    At 7530 mOhm this is a part where the winding, not the core, decides the temperature rise. The data sheet quotes the typical and the maximum separately for a reason: build your budget on the maximum.

    Isat is a magnetic limit, not a thermal one. Isat is the peak current for approximately 30% rolloff at +20 °C. Past it the inductance falls and the ripple climbs, and the current keeps flowing - nothing protects the switch except your own design margin.

    What This Family Is For

    DR125 is the 6.0 mm member of the 12.5 mm family, with current up to 45 A peak. The larger body spreads the winding over more copper, which is where the current headroom comes from.

    • Typical applications: Desktop and servers, DC-DC converters, LCD panels, portable and handheld devices, noise filtering and filter chokes.
    • Peak current and RMS current are different limits on this series; the ripple current adds heating without adding output, so design to Irms for temperature and Isat for headroom.
    • Data sheet 4315.

    Sizing and Layout Notes

    4700 uH sits at the high end of the range, and the trade at that point is explicit: 7530 mOhm of DCR against 0.32 A of saturation headroom.

    The loss budget is the whole story with a power inductor: core loss grows with frequency and flux swing, copper loss grows with current, and the two meet at a different point for every inductance in the series.

    Frequently Asked Questions

    Can I run it above the rated current?
    Briefly, if the peak stays below Isat and the average heating stays within the temperature rise the board can actually remove. There is no built-in protection.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Is the "-R" suffix important?
    Yes - it denotes the RoHS-compliant build. The same inductance without it is a different ordering code.

    Design note: use the maximum DCR for the loss budget, keep the peak current below Isat with margin for the transient, and remember the 40 °C rise assumes free air on the recommended pad.

    Mechanical Dimensions

    eaton-dr-high-power-density-high-efficiency-shielded-drum-core-power-inductors-data-sheet mechanical dimensions and recommended pad layout

    Dimensional drawing and recommended PCB pad layout from the Eaton data sheet. Tolerances and pad dimensions are as printed on the drawing; check the outline against your layout before release.

    Shenzhen Gaorunxin Technology Co., Ltd

    Online message